rear brake mount question

Joined
Feb 27, 2019
Messages
44
Age
59
Location
Ottawa, ON
Bike
'04 ST1300,
Hey all, so I got new rotors all around after discovering the cracked front one. Fronts are on, no issues. Back one,...well.. I got a weird one. During reassembly something isn't lining up. You can see in the pics the caliper mount appears to be too far to the right and is scraping the brand new rotor! Don't want that. It looks to me there should be a washer in between the caliper mount bracket and the wheel spacer. I've seen that before on many older bikes. But I can't find any washer that dropped on the ground, I looked up videos of rear wheel removal and there isn't one, and I looked up online parts fiche and can't see one. One thing that did strike me is that the axle nut is snugged up and you can see how the head of the axle is slightly inside the swingarm. I thought that was a little strange. Normally I see them flush or out just a little bit. Another thing I though was a bit weird was the stopper bolt is in but there's a gap between the stopper pin and the mount bracket.

Any ideas?
 

Attachments

  • IMG_6923.JPG
    IMG_6923.JPG
    65.8 KB · Views: 29
  • IMG_6924.JPG
    IMG_6924.JPG
    55.6 KB · Views: 28
  • IMG_6925.JPG
    IMG_6925.JPG
    64.6 KB · Views: 27
Hey all, so I got new rotors all around after discovering the cracked front one. Fronts are on, no issues. Back one,...well.. I got a weird one. During reassembly something isn't lining up. You can see in the pics the caliper mount appears to be too far to the right and is scraping the brand new rotor! Don't want that. It looks to me there should be a washer in between the caliper mount bracket and the wheel spacer. I've seen that before on many older bikes. But I can't find any washer that dropped on the ground, I looked up videos of rear wheel removal and there isn't one, and I looked up online parts fiche and can't see one. One thing that did strike me is that the axle nut is snugged up and you can see how the head of the axle is slightly inside the swingarm. I thought that was a little strange. Normally I see them flush or out just a little bit. Another thing I though was a bit weird was the stopper bolt is in but there's a gap between the stopper pin and the mount bracket.

Any ideas?
You have a rotor for abs, pictures show it it flat, non abs rotor has a step. 1794792169000.png

1794792219494.png
 
OK, trying to clear up some confusion here.

You have a 04 ST1300 listed as your ride, but posted this in the 1100 Brakes forum.

So, what UP and Al have said is true, but it applies to the 1100, not necessarily the 1300, so we need to sort that out before going any further.

edit: after looking at your pictures it would appear that you have the axle inserted too far to the right inside the swingarm, but it looks like the rotor is still too far to the left? So if you pull the axle further to the left, to align it with the outside of the swingarm, that would just make your rotor interference worse, not better, am I seeing it correctly?
 
Last edited:
If it helps as a comparison, here are photos of mine (1990 bike) installed. The head of the axle bolt does sit inside the swinging arm a little. But your disc is certainly further over to the left than mine, check the wheel castings that are virtually flush with the disc on mine. Also note that your brake disc bolts fit flush into your disc, mine sit on the disc. This would all probably indicate that @Al st1100 has identified the problem correctly.... wrong disc.


DSC_0034.JPGDSC_0035.JPGDSC_0036.JPGDSC_0037.JPG
 
If it helps as a comparison, here are photos of mine (1990 bike) installed. The head of the axle bolt does sit inside the swinging arm a little. But your disc is certainly further over to the left than mine, check the wheel castings that are virtually flush with the disc on mine. Also note that your brake disc bolts fit flush into your disc, mine sit on the disc. This would all probably indicate that @Al st1100 has identified the problem correctly.... wrong disc.
1. its a 1300 not an 1100
2. his rotor is already too far left. The non-ABS rotor that aligns even further left would make his interference worse, not better, but its probably a moot point because that rotor is for an 1100, not a 1300. Maybe the OP has two bikes, and also has an 1100, IDK, but his profile says 1300.
 
1. its a 1300 not an 1100
2. his rotor is already too far left. The non-ABS rotor that aligns even further left would make his interference worse, not better, but its probably a moot point because that rotor is for an 1100, not a 1300. Maybe the OP has two bikes, and also has an 1100, IDK, but his profile says 1300.

Now, I know it's 3am here and I should really be tucked up in bed but........ the photos provided by the OP are definitely from a ST1100 :rolleyes:
 
Now, I know it's 3am here and I should really be tucked up in bed but........ the photos provided by the OP are definitely from a ST1100 :rolleyes:
agreed. I wasn't sure if the 1300 had a similar look, so went online for a few photos and the swingarm is definitely different on the 1300.

so now we're back to the question about correct brake rotor being mounted. The stock non-ABS disk sticks out even further left than the flat one the OP shows, and in his middle photo even the part of the rim where the rotor attaches is halfway over into the caliper gap, so something isn't lining up correctly at all.
 
Also note that your brake disc bolts fit flush into your disc, mine sit on the disc. This would all probably indicate that @Al st1100 has identified the problem correctly.... wrong disc.

That looks to be the case. The flat (ABS) rotor clearly shows the bolt holes to be relieved for the heads of the bolts to fit flush/into the rotor. The other rotor has no such provision.

Hm. Actually I can't be sure from the pic as it appears I'm seeing the rear of the second rotor. Still the wrong rotor seems to be the answer.
 
The stock non-ABS disk sticks out even further left than the flat one the OP shows,

No it doesn't. if you look at the rear wheel castings on my photos you will see that the rotor sits flush or even very marginally inside them. The OPs incorrect disc sits to the left of them. That means that the stock non-ABS disc sits further to the right!!
 
No it doesn't. if you look at the rear wheel castings on my photos you will see that the rotor sits flush or even very marginally inside them. The OPs incorrect disc sits to the left of them. That means that the stock non-ABS disc sits further to the right!!
Yep, tripped over the very same "problem" quite a while ago...
The painted black, inner section of the OP's rotor ID's it as aftermarket, offered as compatible with GL1500 and ST1100... but doesn't specify which of the 3 base model variants...
Short story: doesn't fit the non-ABS, resting on the shelf ever since...
 
No it doesn't. if you look at the rear wheel castings on my photos you will see that the rotor sits flush or even very marginally inside them. The OPs incorrect disc sits to the left of them. That means that the stock non-ABS disc sits further to the right!!
you're right.

I took a closer look today at the actual disk and now I see what you mean. The stock rotor surface protrudes to both the right and the left from the base that bolts to the rim (has a T shape), whereas the one the OP has mounted is flat (has an I shape).
 
Back
Top Bottom