3D Printed Mirror filler pieces for ST1100

[jdmccright]

To all,

My next items I've been able to finish and finally offer are the inner pieces that fill in between the mirror and fairing. These are 3D printed in black ABS. Haven't added any special lettering or other graphics but I can if desired, like "HONDA" or "ST1100" or whatever custom.

Cost is $10 (USD) per pair. Shipping is $6 in the USA, and $15 international for up to 3 pairs.

 

[Computek]

Are you still offering these and how would I purchase? Thanks!

 

[jdmccright]

Are you still offering these and how would I purchase? Thanks!

Sorry, I didn't see your post until now. Yes, I make them as needed. Send a PM and we can exchange details.

 

[Oldbikefixr]

I've had these installed for a while now, getting close to three years. Still fit properly, no UV degradation. Shame I have only the one 1100.

 

[DeanR]

I've had these installed for a while now, getting close to three years. Still fit properly, no UV degradation. Shame I have only the one 1100.

Wish I had done the white lettering like you did. Looks good

 

[Nexus]

I've had these installed for a while now, getting close to three years. Still fit properly, no UV degradation. Shame I have only the one 1100.

I don't own an 1100 so just curious: What usually goes there?

 

[jdmccright]

I don't own an 1100 so just curious: What usually goes there?

A blank plug fits in there that uses a metal clip to hold it. Very common to bend that clip trying to reinstall it, making the plug loose or even fall out. The one I designed doesn't need that clip.

 

[Larry Fine]

I don't own an 1100 so just curious: What usually goes there?

 

[jdmccright]

Oy vey I was responding to the carb plug, not the piece you show. Yes, the OEM piece that goes between the fairing and mirror is painted to match, held in with a push-in plastic fastener.

 

[Larry Fine]

Oy vey I was responding to the carb plug, not the piece you show. Yes, the OEM piece that goes between the fairing and mirror is painted to match, held in with a push-in plastic fastener.

My bad. (That's funny, you don't look Jewish! )

https://www.partzilla.com/product/honda/77121-MT3-000ZA?ref=3780a6de38eef51651ccc1312c842d310fba30e1

 

[Oldbikefixr]

I don't own an 1100 so just curious: What usually goes there?

These replace the featureless snap-in covers that were stock. They cover an access hole. Allows access to the adjustment screws on either rear carb without having to remove the plastic side covers. You can also remove the two aft spark plugs using these two openings.

 

[jdmccright]

These replace the featureless snap-in covers that were stock. They cover an access hole. Allows access to the adjustment screws on either rear carb without having to remove the plastic side covers. You can also remove the two aft spark plugs using these two openings.

These are diferent than what Nexus was asking about. Sorry if I added to the confusion.

I do print replacements for both parts. The filler panels are not painted. The carb access plugs are only accent painted. Those are shown here:

ST1100 Carb Access Cover / Maintenance Cap : 3D-Printed Replacements | Vendor Announcements

I have designed 3D printed replacement covers for the access holes by the knees. These replace both the plastic cap 77121-MT3-000ZA and metal clip 90666-SD4-003. Each pair is $10 USD I have two different logos, the Honda wing and "ST1100" so far but can do custom if desired for an add'l fee. The...

www.st-owners.com

 

[Nexus]

Yeah, I was asking about the square covers. I figured out the mirror ones.