Have nothing further to add, anything on your end ?
Update: Last week I cleaned the VRR male connectors with 600grit paper (theory is oxide exists that is causing high resistance) and the contacing "bars" of the female terminal.
To date i've taken it on about 6 30 minute rides and constantly have 14.3 Volts present at the battery terminals.
I'm not positive this is the "sure fire fix" but maybe. After 2 months goes by and no issues I may pronounce it a victory.
If so I'd say this will be a large learning on deceptive "corrosion" that you would think not an issue intuitively by looking.
Now I need to go and check my valve adjustment. Perhaps a new chapter is coming.
I do want to say with a sincerity "Thanks to all that contributed to solving this issue" - I would cerntainly not have been tugging on terminals to find / get this far. Huge thanks!
Paul
+1 on both :wink:Nothing wrong with the 28A system as a whole. The problem as you've found is neglect(out of sight,out of mind).
I actually apply thermal grease (the white stuff as used on CPU-coolers/heat-pipes) on the backside before bolting the VRR back onto the footrest plate.It is a heat sink to help draw heat away from regulator.
+1 on both :wink:
An annual squirt of protective substance (like ACF-50) on connectors, fuse-box, etc... helps avoiding such woes...
I actually apply thermal grease (the white stuff as used on CPU-coolers/heat-pipes) on the backside before bolting the VRR back onto the footrest plate.
As long as not seriously overloaded, the 26A system is pretty reliable... thousands of ST's are running out there...Not a good ride day if the all important 'smoke' escapes .
As long as not seriously overloaded, the 26A system is pretty reliable... thousands of ST's are running out there...
Problems occur due corrosion on the crimp-connectors, increasing contact resistance thus generating heat increasing the resistance even further, which causes voltage drops, thus raise of current flowing...
Or serious overload (heated panties and such :wink: ), the increased current causing heat on named contacts, starting the same deadly circle...
The 26A system has like 10A surplus avail for accessories, enough to run a set of heated handles plus a standard car-stereo maybe...
Depending how big that mattress is, thus how long that pump has to be operated to fill that "air-dome" and how much amps that "sucker" draws ;-)...likely would not be an issue using a Coleman mattress pump to air up a mattress...
Depending how big that mattress is, thus how long that pump has to be operated to fill that "air-dome" and how much amps that "sucker" draws ;-)
The OEM Yuasa battery is rated with 12Ah when new... lets guestimate a conservative average of an aged battery at 10Ah... that's 1A for 10 hours, 5A for 2 hours, 10A for 1 hour, etc...
Unless you'll have the engine running while supplying that Coleman thingie... leaves the issue of neighbours (nagbours?) complaining ;-)
Update: Last week I cleaned the VRR male connectors with 600grit paper (theory is oxide exists that is causing high resistance) and the contacing "bars" of the female terminal.
To date i've taken it on about 6 30 minute rides and constantly have 14.3 Volts present at the battery terminals.
I'm not positive this is the "sure fire fix" but maybe. After 2 months goes by and no issues I may pronounce it a victory.
If so I'd say this will be a large learning on deceptive "corrosion" that you would think not an issue intuitively by looking.
Now I need to go and check my valve adjustment. Perhaps a new chapter is coming.
I do want to say with a sincerity "Thanks to all that contributed to solving this issue" - I would cerntainly not have been tugging on terminals to find / get this far. Huge thanks!
Paul
Looking for a 28A unit to replace one with an open winding. Commuter bike with 130k on clock. Don't really need a 40A piece.