Fern creek
Rear caliper and bracket help!!
- Thread starter jzmaes1991!
- Start date
You might be up the creek.
But don't worry there are plenty of paddles
Upt'North.
But don't worry there are plenty of paddles
Upt'North.
- Joined
- Sep 5, 2018
- Messages
- 1,765
- Age
- 70
- Location
- Newlyn, Penzance, Cornwall, UK
- Bike
- 2000 ST1100Y
- STOC #
- 9006
It looks to me like one of the pad slider pins and holds the caliper together. Should also have a rubber boot on it......
That's my current look. It seems they just slide on? Nothing really holding them on the bracket besides two slider pins??? I was able to screw it in further after mounting the brack on the swing arm like you.mentioned
I would use a thread file on the bolt but I'm guessing you probably won't have one. If you're careful with a nail file, don't tell Er'Indoors, just lightly clean the threads off.
Ideally run a tap through the bracket if you can get hold of one.
Upt'North.
Ideally run a tap through the bracket if you can get hold of one.
Upt'North.
So I'm also trying to take the brake pad holder pin out. Unscrewed it with a screwdriver and cant seem to get the rod out
- Joined
- Sep 26, 2011
- Messages
- 757
- Location
- Springville, Indiana
- Bike
- 2000 ST1100
- 2024 Miles
- 001743
- STOC #
- 8497
Looks like you are 2 hrs from my place.
FYI: check my thread for the next Indiana Tech Event.
www.st-owners.com
You are welcome to join us!
FYI: check my thread for the next Indiana Tech Event.
2020-09-19 Indiana Tech Event Springville, Indiana [cancelled] | Technical Events
Date is set for my next Tech Event for Indiana. Saturday September 19, 2020. Same time as last events. Officially starting at 9 am. But I will have the garage open by 8 am. All are welcome, no matter what you ride! Lunch will be similar to past events, sometime around 12 noon. Depending on...
You are welcome to join us!
- Joined
- Sep 5, 2018
- Messages
- 1,765
- Age
- 70
- Location
- Newlyn, Penzance, Cornwall, UK
- Bike
- 2000 ST1100Y
- STOC #
- 9006
It comes out with (I think) a 5mm allen key. The brass screw is just a cap...
That bolt angle looks all wrong in the picture.
Upt'North.
Upt'North.
- Joined
- Sep 26, 2011
- Messages
- 757
- Location
- Springville, Indiana
- Bike
- 2000 ST1100
- 2024 Miles
- 001743
- STOC #
- 8497
Correct, note for future, break those loose before the bracket is removed.
- Joined
- Sep 5, 2018
- Messages
- 1,765
- Age
- 70
- Location
- Newlyn, Penzance, Cornwall, UK
- Bike
- 2000 ST1100Y
- STOC #
- 9006
Don't think I am being nasty, but, having been where you are many times in the last 50-odd years, I now take lots of photos before and during disassembly of new bikes, cars etc...
Taking the whole thing to the shop. I def thing something is wrong will update. Also may need advice for bleeding when I get back
New to this. My bad. Juat has been frustrating.
Thank you. Alot to learn lol
- Joined
- Sep 5, 2018
- Messages
- 1,765
- Age
- 70
- Location
- Newlyn, Penzance, Cornwall, UK
- Bike
- 2000 ST1100Y
- STOC #
- 9006
I know exactly how you feel - some of my major screw-ups are currently in Newlyn harbour!!
- Joined
- Sep 5, 2018
- Messages
- 1,765
- Age
- 70
- Location
- Newlyn, Penzance, Cornwall, UK
- Bike
- 2000 ST1100Y
- STOC #
- 9006
THAT ONE WASN'T ME!!!!!