I have used PayPal for my LED's with Cindy......12 days later they have arrived in Bremen - Germany.
No problem at all !! Great light on my ST1300
No problem at all !! Great light on my ST1300
Ok sent Cindy an email with the above info and she replied requesting my 'tracking number' so she can send an invoice.do not send pay pal information. Send her your shipping address and how many of each you want, she will send you an excel invoice.
22% off at on 3/29 + free ship during their anniversary sale.
Same with me.....as I said, 12 days later..... I'm happyStill awaiting mine. She told me they'd been shipped already (I'd inquired about shipping status on the 16th of March; quoted $29 USD product, $9 shipping, $1.52 Paypal on 6th Mar, ordered 7th.). She further stated she didn't send the "colorful" box due to cost of shipping being exceeded .
You fared better than me. I payed via paypal on Feb 27th and heard nothing back. I inquired on March 8th asking for tracking information and Cindy replied that she had shipped my order on March 6th and provided a tracking number. However, the tracking number actually showed that the shipping order was created on March 8th (she lied). The tracking information now shows that my order is in Houston so, hopefully, I will get it soon.FWIW, I started my order process on Feb 28, and finally received mine on March 22.
Similar to me.....look at my previous post.Still awaiting mine. She told me they'd been shipped already (I'd inquired about shipping status on the 16th of March; quoted $29 USD product, $9 shipping, $1.52 Paypal on 6th Mar, ordered 7th.). She further stated she didn't send the "colorful" box due to cost of shipping being exceeded .
I had considered doing that but by the time I got round to it Amazon was OOS. My G6s took about two weeks and arrived without incident.GadgetGuy1230 said:Can't wait to fit them, but I would probably pay $20 more to get them from amazon in 2 days.
Exact same thing happened to me. Took a lot less (?) time to get sorted though.Catmandu2 said:the right one popped out and dropped down into the main beams reflector. I read somewhere that this can happen
Ditto.if you fully seat them in their sockets,,, contact is not made. Pull them out a bit,,, and away they go.
I feel your pain. I was able to put the bulbs and sockets back it successfully the first time by trying to push on the edges of the sockets and not the middle. That's what squirts the bulb out. One thing I wish I'd done is use a bit of silicone grease (carefully applied) around the sockets so they slip in and possibly are removed more easily down the road.But I am wary to push the bulbs back into the main housing in that state,,, given what happened to the original bulb dropping out... The way the socket is designed,,, pushing the bulb/socket in, or pulling it out, causes the bulb to want to squirt free.
That would/will be fine by me. :grin: I much prefer that over the legal modulation of the beams.And my SDC modulator has them flashing,,, rather than pulsing.
Had to drive out too buy pipe cleaners and sticky tape.Exact same thing happened to me. Took a lot less (?) time to get sorted though
Yes,,, same thought occurred to me. I have some electrolitic grease to apply to the taper section of the socket.One thing I wish I'd done is use a bit of silicone grease (carefully applied) around the sockets so they slip in and possibly are removed more easily down the road.
I am going to start out using my SDC. One thing I have always prefered about it, over other brands, is that it was effective on both high and low beams. Kisans unit looks good,, and only operates on high beam. It is pricey too, but effectiveness is the over riding concern. At some future point,,, I can always return the SDC to my CB1000c (which I stole it from),,, and test out the Kisan. It may prove adequate in operation when now paired with the F2's. Cat'That would/will be fine by me. I much prefer that over the legal modulation of the beams.
These look good, but no reviews yet. It appears that they plug in with a cord instead of directly. I assume this makes it easier, but I'd love to get some feedback after you install them.https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1